AS/NZS 1163 ERW Circular Hollow Section

Send Inquiry
AS/NZS 1163 ERW Circular Hollow Section
Details
ASTM A500 ERW round pipe is cold-formed electric resistance welded structural hollow tube widely used in North American, Australian and Middle Eastern construction. Supplied in Grade B, C and D, this tube is designed for static structural loads instead of pressurized fluid transport.

Brisk Steel provides custom cut lengths, multiple surface treatments and EN 10204 3.1 MTC for your structural projects.
Category
ERW Pipe
Share to
Description

Tianjin Brisk Metalwork Co., Ltd. is one of the leading manufacturers and suppliers of as/nzs 1163 erw circular hollow section in China. We have world-leading production equipment and strong manufacturing capabilities. Please feel free to buy bulk durable as/nzs 1163 erw circular hollow section from our factory.

 

 PRODUCT

Tianjin Brisk Steel focus on produce and supply hollow section and steel pipe

AS/NZS 1163 ERW Circular Hollow Section
AS/NZS 1163 ERW Circular Hollow Section
AS/NZS 1163 ERW Circular Hollow Section
AS/NZS 1163 ERW Circular Hollow Section

Product Introduction

 

 

AS/NZS 1163 is the joint Australian and New Zealand standard for cold-formed welded structural hollow sections, commonly known as CHS (circular hollow section). This page focuses on AS/NZS 1163 ERW round pipe, manufactured for static structural loads, not for pressurized fluid transmission.

 

Unlike pressure pipeline products designed to carry liquid or gas under internal pressure, AS/NZS 1163 CHS is engineered to resist external static loads such as compression, bending and lateral force. Australian and New Zealand local codes often reference AS/NZS 1163 for civil works, mining infrastructure and coastal construction where corrosion risk must be carefully considered.

 

This standard is widely specified for construction, infrastructure, mining and coastal projects across Australia and New Zealand. The suffix L0 means low-temperature Charpy impact test requirement, the most common option for general building works.

 

Available Steel Grades & Material Data

 

 

Chemical Composition (Max %, Heat Analysis)

 

Grade C Si Mn P S CEV
C250 / C250L0 0.12 0.05 0.50 0.03 0.03 0.25
C350 / C350L0 0.20 0.45 1.60 0.03 0.03 0.43
C450 / C450L0 0.20 0.45 1.70 0.03 0.04 0.50

 

Mechanical Properties

 

Grade Min Yield Strength (MPa) Tensile Strength (MPa) Min Elongation %
C250 / C250L0 250 340 – 500 20
C350 / C350L0 350 430 – 600 18
C450 / C450L0 450 500 – 650 12

 

Note: C250L0 is the cost-effective general-purpose grade for simple frames, railings and secondary bracing. C350L0 is the most popular selection for mainstream Australian structural projects with medium load demand. C450L0 delivers high yield strength to reduce pipe size and weight for heavy-load structural members.

 

👉 Read more: [More details please check the Standard AS/NZS 1163 | Brisk Steel]

 

Factory Inspection & Witness Test Requirements for Aussie Projects

 

 

AS/NZS1163 mandates tensile test and cold flattening test for each production batch. Dimensional and visual inspection are also compulsory.

Brisk Steel allows third-party witness inspection before shipment.

 

  • Eddy Current or Ultrasonic testing for ERW weld seam
  • Charpy V-notch impact test for L1/L2 grades
  • PMI positive material identification
  • Zinc coating thickness test for HDG CHS

 

Coating & Storage Guidance for Sea Shipment to Australia

 

 

Long sea voyage plus high humidity in shipping containers creates corrosion risks, especially for HDG tubes shipped to coastal Australian ports.

 

  • Bare black CHS: Apply temporary anti-rust oil before packing for ocean transit.
  • Hot dip galvanised CHS: Avoid fully sealed airtight wrapping. Trapped condensation will cause white rust on zinc surfaces. PVC packaging is required.
  • After arrival: Store tubes off the ground in well-ventilated warehouse space. Keep away from direct rain and salt spray. Stacking should allow air circulation between layers.

 

👉 Read more: [How Should Hot-Dipped Galvanized ERW Pipe Be Stored? | Brisk Steel]

 

Frequently Asked Questions (FAQ)

 

Q: Will Australian surveyors check heat numbers on site?

A: Yes. Heat number cross-verification between pipe tags and MTC is standard practice. Any mismatch will trigger hold or rejection.

Q: What happens if wall thickness fails site sampling inspection?

A: The whole batch may be put on hold. You will need to negotiate with the surveyor, which causes port storage charges and project delay. Brisk Steel carries out full dimensional sampling before loading.

Q: Can the tubes be cut, drilled and welded on site?

A: Yes, AS/NZS1163 carbon steel CHS has good weldability. Fabrication work should follow Australian welding standards and engineer specifications.

Q: Is AS/NZS 1163 CHS suitable for seaside projects in Australia?

A: Yes, but hot dip galvanised surface treatment is strongly recommended for coastal salt spray environments to extend service life.

 

Send your specifications including outer diameter, wall thickness, steel grade, required length and surface finish to our sales team. Brisk Steel Factory will provide formal quotation, lead time and full export document support for your ASTM A500 ERW round pipe project.

 

Related: Electric Resistance Welded (ERW) Pipe

Contact now

MACHINE EQUIPMENT
ERW PRODUCTION LINE 2
UNCOILING PROCESS
BRISK ERW PIPE PRODUCTION LINE

Hot Tags: as/nzs 1163 erw circular hollow section, China as/nzs 1163 erw circular hollow section manufacturers, suppliers, factory, curved erw pipe, erw pipe exporter, erw pipe globalization, erw pipe legal impact, erw pipe with different diameters, hexagonal erw pipe

Send Inquiry